Ways To Install A Door

You have a door to your house that is faulty or missing. This demands that you fix it firmly in place. But just what are the procedures to follow? Having a firm knowledge of this is necessary to be able to do a great job. We draft and dedicate the entire length and breadth of this article to do just that.

How To Install A Door

To be able to do an awesome job, there are some tools and materials you will have to garner. Then there are those steps you will have to follow.

Tools and Materials Required

• Door installation kit
• Screws
• Hammer
• Screwdriver
• Nails
• Saw
• Floor leveler
• Mortar
• Shovel

Below are the tools and materials you will need for the job:

Step-by-step Procedures

Follow these procedures to be able to get the job done:

Step I: Mark out the Dimensions

Start by marking the dimensions of the opening versus the one for the door you want to fix in place. These two dimensions have to tally as much as possible. Nonetheless, there ought to be some meaningful space to allow for smooth movements and easy fitting thereafter.

Generally speaking, this space should measure roughly ½ inches larger than the actual size of the door you intend to fix in place. This is necessary to give sufficient space for the door also to swing smoothly once fit.

Step II: Level the floor

Chances are that the floor in the area in which the door is to be fit is not level. That means you will have to make it flat and level. If you leave it that way, the door will generally struggle to open and close. That will also lead to scratches and possibly premature damage to the door altogether.

To do this, use the level checker to find out whether the floor is level or not. If it is not, then you have to do so typically by flattening the affected portions using a sickle and a saw.

Step III: Fix the Door Frame

It is on the door frame that the door is subsequently attached. After leveling the floor, you have to fix the frame firmly in place. To do this, slot the frame in the opening that you have already measured out.

Follow this procedure by applying some mortar to the spaces between the wall and the frame. While at it, maintain the blocks away from the hinges to stop them from interfering with the shimming. Cover the nail holes with the casing thereafter.

Step IV: Fix the door

Having installed the frame, the time has now come for you to fix the door onto the frame. Simply lift the door and place it in the space. Then, place the hinges on the frames and use some screws and a screwdriver to fasten the door in place.

You will no doubt require extra support from the others around you if you lack the necessary muscle power. Fasten the door thoroughly to prevent the same from possibly falling off when opened and closed.

Step V: Finish the floor

With the door firmly fixed, you now have to finish the floor. Plaster the floor and leave the same to dry. You should pour water there twice a day to aid in fastening. Be sure that the door can open and close smoothly after the floor has been properly made.

To ensure this, open and close the door several and watch as it swings. Needless to say, make appropriate arrangements to eliminate any obstacles that may hamper these smooth movements.

Step VI: Test the door

Before you call it a day, you have to test the door. Open and close it a couple of times and note how it responds to the prompts. Check out for inconsistencies that may arise and then remedy them appropriately. Particularly, adjust the jambs to see to it that all the sides of the door hit the stop at the same time.

Step VII: Shim behind hinges

Chances are that at this time, there could be some spaces left in between the walls and the hinges or the frame of the door. This is the best time to remedy the issue. To do this, you will generally have to fill the whole gaps that are left or exist between these open spaces. Drive the screw in to achieve this.

In case the framing on the rough opening appears to be twisted, place the shims in such a way that the jambs are at a right angle to the wall. With the shims firmly in place, see to it that the jambs are flush with the drywall. Nail the shims finally in place using the 15-gauge nails.

Step VIII: Secure the latch side

Finish off by securing the latch sides. Do this by inserting and securing the shims at positions that are roughly 4 inches from the top of the door and the same distance from the floor. Nail these shims in the same way you did to the hinges.

Do not use longer screws in the plate holes of the latch as they are able to split the framing lumber when engaged. Instead, use those that are moderately sized. They have the added advantages of being easier to make do with.

Final Verdict

Installing your door is an undertaking that you can never tackle recklessly. Remember, the kind of work you do has a bearing on the experience you are likely to accrue from it all. Do something shoddy and end up with huge problems when attempting to open and close the door.

On the flip side, do something great and enjoy unparalleled peace of mind as you open and close the door. What does that mean? You want to read the explanation we have given out carefully and adhere to them diligently. If you are uncertain, the best you should do is consult a trained expert to help you out!